FloorMate SpinScrub Hard Floor Cleaner
      Back to home
      1. Hoover Support Library
      2. Troubleshooting
      3. FloorMate SpinScrub Hard Floor Cleaner

      FloorMate SpinScrub Hard Floor Cleaner

      This article contains information on how to fix issues on the FloorMate SpinScrub Hard Floor Cleaner.

      fh40010b

       

      CAUTION: We highly advise to use the correct cleaning solution for this unit, any other cleaning solution could cause excess foaming and a motor bypass. You will notice this because the unit will leak from the exhaust port.

      Mode Selector Dial

      The mode selector dial turns the brushes on and off.


      1. For dry debris pickup, turn the dial to the VACUUM position. In this position, the brushes will not rotate and are raised off the floor surface.
      2. To wet clean with brushes turned ON, turn the dial to the WASH position.
      3. For wet pickup, turn the dial to the DRY position.

       

      WARNING: To reduce the risk of injury from moving parts, unplug cleaner before servicing.

      Cleaning the Filter

      The tank lid contains a washable, reusable filter. Clean this filter when suction is low or reduced.

       

      1. Remove Dirty Water Tank and lid (2.15 & 2.16).
      2. Remove filter lid (A), then remove filter (B). 2.15a2.17a 
      3. Remove loose debris from filter by tapping the filter or gently brushing using your hand.
      4. The filter may also be rinsed for additional cleaning, allow the filter to air dry for 24 hours.
      5. Replace filter lid and press down firmly until snapped in place.
      6. Dry or loose debris will also collect on the filter screen located in the tank lid 
        1. To remove debris from screen, remove the pleated filter from the lid. Remove debris from the screen (C), screen may also be cleaned by rinsing it under running water
      7. Reposition pleated filter in lid. Replace lid onto Dirty Water Tank, pressing down firmly until snapped in place.
      8. To replace Dirty Water Tank, place bottom of tank behind ledge (E) and push tank straight into cleaner body until it is locked in place.

      Cleaning the Nozzle

      Your cleaner is equipped with a removable nozzle for easy cleaning. We suggest cleaning after every use!

      If your unit has a change in suction power, ensure you clean your nozzle & brush assembly.

       

      1. Slide the two nozzle release latches (A) outward. 4.1
      2. Remove nozzle (B) by pulling straight out.
      3. Rinse nozzle under running water. Remove debris from squeegee (C) and wipe wish a damp cloth.
      4. To replace nozzle, make sure latches (D) are out. Cleaner should be in the upright position for easier assembly of the nozzle.
      5. Align middle section (E) of nozzle with opening (F) on cleaner. While holding nozzle in place, slide latches inward to lock in place.

       

       

       

       

      Cleaning the Brush Assembly

      The brush assembly can be removed for easy cleaning. We suggest cleaning after every use!

       

       

      1. Place handle in upright position, Remove tanks to prevent leaking and set aside.  4.6
      2. Pull the two nozzle release buttons (A) out to remove nozzle.    
      3. Tilt cleaner back so handle rests on floor. Push two  brush release buttons (B) and remove the brush assembly.
      4. The brushes can be rinsed until clean.
      5. To replace brushes, align post (C) on brush assembly with hole (D) on bottom of cleaner. Turn brushes slightly until post fits easily into hole. Press brush assembly firmly to snap into place.
      6. Return cleaner to upright position. Replace nozzle, making sure latches (E) are out. Align middle section (F) of nozzle with opening (G) on cleaner.
      7. While holding nozzle in place, slide latches inward to lock in place. Replace tanks.

      PRO TIP: If you remove debris from brush assembly before rinsing, cleaning with be a breeze!